Presented here below you will find some reliable data about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a tub isn't specifically brain surgery, but it does need strong plumbing, carpentry, as well as often, tiling skills. Replacing an old tub with a brand-new one is also a moderately tough task. If the old tub is easily easily accessible, the task can move quickly; if you need to open up a wall surface to remove the old tub as well as place the brand-new bathtub, the task is much harder. In either instance, the task is within a home handyman's skills, although you will certainly require an assistant to move out the old tub and set in the brand-new one. See to it you have actually certified yourself for the job and fit trying it. As opposed to working with a contractor to take over a halfway-completed job, it is much better to take into consideration using one prior to you start. Chances are you may need a professional plumber to make tube connections.
This short article will assist you set up a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and also do not require to transform the setup of your previous water supply pipelines.
Your devices and also product list must make up the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the limited gain access to that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the staying water that will originate from the pipelines. When the supply pipes have actually been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming during this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Prior to carrying on to fit the new faucets, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and also the other end provides a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers remain in place in between the faucet and the sink. Safeguard the tap in place with the supplier provided backnut. When the faucet is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous type ought to be attached to the tap ends initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are practical in evenly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the tub till the spirit level checks out degree.
To mount taps, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the same for the other tap.
Activate the water and inspect all joints as well as brand-new pipework for leakages and tighten them if required. Fill up the bath tub as well as also check the overflow outlet as well as the regular electrical outlet for leakages.
Finally, repair the bath paneling as explained in the maker's user's manual. Tiling and also securing around the tub must wait up until the tub has actually been utilized a minimum of once as this will settle it into its final position.
Preparing for the Installation
Firstly, the sustaining structure provided with the bathroom must be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to prevent pressure on the bath tub.
Fit the adaptable tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to now be ready to be suited its final placement.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to split a rigid seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, bring about problems with wetness as well as feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and cartridges, as well as are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked paper or soft rope. Remember to constantly load the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealant can fracture fairly very early if you do not take into account this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is suggested to fit the tiles utilizing water-resistant or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted person who reads on How to Install a Bathtub Yourself, I assumed sharing that piece was a good idea. Loved our blog posting? Please share it. Let others check it out. Thank you so much for taking the time to read it.
Free Estimates